Effects of 4He impurities on 3He nuclear spin-lattice relaxation in hcp solid 3He

Nuclear spin-lattice relaxation properties of hcp solid ³He with ⁴He impurities have been studied. At temperatures below the exchange plateau region, three kinds of relaxation time were observed. To analyze the data, a phenomenological four-bath model was developed, the four baths being the Zeeman bath, the phonon bath, an X-bath, and a Y-bath. The X-bath consists of the exchange bath and a part of the ⁴He-⁴He elastic interaction bath. The Y-bath is the main part of the elastic interaction bath. We measured the concentration dependence of the energy constants of all the baths, as well as the temperature and concentration dependences of the three kinds of relaxation time. The relaxation behavior corresponding to the process between the X-bath and the Y-bath could not be expressed by a single exponential function of time and the relaxation rate was strongly dependent on the concentration. This process may be related to the internal thermal equilibrium process within the elastic interaction bath. The impurity-dependent relaxation time between the X-bath and the phonon bath had a temperature dependence of T ^–n with n = 7.4±0.3.     

Dielectric Dispersion of Polycrystalline Aluminum Nitride at Microwave Frequencies

Complex permittivity of polycrystalline AlN was measured over the frequency range 100 MHz to 13 GHz using reflection coefficient and cavity resonator methods. Dielectric relaxation peaks of loss tangent were observed in the frequency range 200 MHz to 3 GHz. The maximum value of loss tangent was ∼200 × 10⁻⁴. Relative permittivities decreased by ∼4% with increased frequency at the region of relaxation peaks. It was shown that these dispersion frequencies were inversely proportional to the grain sizes of AlN and independent of purities and processes. Model calculations for elastic vibration of a single-crystal grain of AlN were performed to investigate the origin of the dielectric dispersion due to piezoelectric effect. The calculated results of elastic sphere and 14-faced-polyhedron models showed a good quantitative agreement with the observed dispersion frequencies, which suggested that the dispersion was due to a piezoelectric vibration of a single grain of AlN ceramics at microwave frequencies.     

Effects of heated seats in vehicles on thermal comfort during the initial warm-up period

Eight subjects participated in a subjective experiment of eight conditions to investigate the effects of heated seats in vehicles on skin temperature, thermal sensation and thermal comfort during the initial warm-up period. The experimental conditions were designed as a combination of air temperature in the test room (5, 10, 15, or 20 °C) and heated seat (on/off). The heated seat was effective for improving thermal comfort during the initial warm-up period when air temperature was lower than 15 °C. Use of heated seats prevented decreases in or increased toe skin temperature. Heated seats also increased foot thermal sensation at 15 and 20 °C. Optimal thermal sensation in contact with the seat was higher when air temperature was lower. Optimal skin temperature in contact with the seat back was higher than that with the seat cushion. Moreover, these optimal skin temperatures were higher when air temperature was lower.     

A coaxial pulsed plasma thruster using chemical propellants

Pulsed plasma thrusters (PPTs) have the advantages of mechanical simplicity and robustness compared to other electric propulsion systems. However the thrust power ratio of PPTs is lower than that of other electric propulsion systems. To enhance the thrust performance of the PPT, we propose to use several combustible solid chemicals as coaxial PPT propellants to replace Teflon^® (Polytetrafluoroethylene: PTFE). With the design, the force obtained thermodynamically is expected to augment the PPT thrust power ratio with the help of the chemical energy contained in the propellants. As a result, the thrust power ratio is increased using hydroxyl-terminated polybutadiene-ammonium perchlorate (HTPB-AP)-based propellants compared to the case of ordinary Teflon. The discharge current and voltage waveform does not change even when the propellant is changed. These findings could indicate that the impulse bits by gasdynamic contribution are lager in the case of chemical solid propellants than in the case of Teflon.     

Magnetization Reversal by Electrical Spin Injection in Ferromagnetic (Ga,Mn)As-Based Magnetic Tunnel Junctions

We report current-induced magnetization reversal in a ferromagnetic semiconductor-based magnetic tunnel junction (Ga,Mn)As/AlAs/(Ga,Mn)As prepared by molecular beam epitaxy on a p-GaAs(001) substrate. A change in magneto-resistance that is asymmetric with respect to the current direction is found with the excitation current of 10⁶ A/cm². Contributions of both unpolarized and spin-polarized components are examined, and we conclude that the partial magnetization reversal occurs in the (Ga,Mn)As layer having smaller magnetization with the spin-polarized tunneling current of 10⁵ A/cm².     

Mass recovery adsorption refrigeration cycle—improving cooling capacity

The study investigates the performance of two-bed, silica gel-water adsorption refrigeration cycle with mass recovery process. The cycle with mass recovery can be driven by the relatively low temperature heat source. In an adsorption refrigeration cycle, the pressures in adsorber and desorber are different. The chiller with mass recovery process utilizes the pressure difference to enhance the refrigerant mass circulation. Cooling capacity and coefficient of performance (COP) were calculated by cycle simulation computer program to analyze the influences of operating conditions. The mass recovery cycle was compared with conventional cycle such as the single stage adsorption cycle in terms of cooling capacity and COP. The results show that the cooling capacity of mass recovery cycle is superior to that of conventional cycle and the mass recovery process is more effective for low regenerating temperature.     

Design of experiments for stacking sequence optimizations with genetic algorithm using response surface approximation

This study describes a new method of experimental design to obtain a response surface of buckling load of laminated composites. Many evaluations for genetic algorithms for stacking sequence optimizations require high computational cost. That evaluation cost can be reduced by an approximation using a response surface. For a response surface for stacking sequence optimizations, lamination parameters are adopted as variables of the approximation function of the entire design space instead of ply angles for each ply. This study presents, proposes and investigates a new method of experimental design in detail. For most analytical tools, stacking sequences is demand as input data and lamination parameters cannot be applied directly to the tools. Therefore, the present study proposes and applies a new D-optimal set of laminates to the stacking sequence optimizations of the problem of maximization of buckling load of a composite cylinder. The new experimental design is a set of stacking sequences selected from candidate stacks using D-optimality. Consequently, the D-optimal set of laminates is shown to be effective for design of experiments of response surfaces for maximization of the buckling load of composite structures.     

A novel polarizer‐free dye‐doped polymer‐dispersed liquid crystal for reflective TFT displays

Abstract— A novel preparation method for dichroic dye‐doped polymer‐dispersed liquid crystals has been developed. This was achieved by creating a porous polymer matrix first by washing out the liquid crystal from a polymer‐dispersed liquid crystal (PDLC), which is then refilled with dye‐doped liquid crystal. Optimizing the liquid crystal used in the refilling results in decreased turn‐on voltage and faster response time. Poster‐standard reflectivity and newspaper‐standard contrast was demonstrated with a 3.8‐in. QVGA reflective TFT display with a drive voltage of 10 V.     

Application of an ultrahigh-resolution scanning electron microscope (UHS-T1) to biological specimens

In 1985 we developed an ultrahigh-resolution scanning electron microscope with a resolution of 0.5 nm. It is equipped with a field emission gun and an objective lens with a very short focal length. In this study we report a survey of some different preparation techniques and biological specimens using the new scanning electron microscope. Intracellular structures such as cell organelles were observed surprisingly sharper than those observed by ordinary scanning electron microscopes. However, at magnifications over 250,000 X, platinum particles could be discerned as scattered pebbles on the surface of all structures in coated materials. Using an uncoated but conductively stained specimen, we successfully observed ribosomes on a rough endoplasmic reticulum at a direct magnification of 1 million. In these images some protrusions were recognized on the ribosomes. Ferritin and immunoglobulin G were used as samples of biological macromolecules. These samples were observed without metal coating and conductive staining. The ferritin particles appeared as rounded bodies without any substructure on the surface and immunoglobulin G as complexes of three-unit bodies. In the latter the central body might correspond to the Fc fragment and two side ones to Fab fragments. We assume that ultrahigh-resolution scanning electron microscopy is an effective means for observation of the cell fine structures and biological macromolecules. It will open a new research field in biomedicine.     

High temperature superconductor micro-superconducting-quantum-interference-device magnetometer for magnetization measurement of a microscale magnet

We have developed a high temperature superconductor (HTS) micrometer-sized dc superconducting quantum interference device (SQUID) magnetometer for high field and high temperature operation. It was fabricated from YBa2Cu3O7-delta of 92 nm in thickness with photolithography techniques to have a hole of 4x9 microm2 and 2 microm wide grain boundary Josephson junctions. Combined with a three dimensional magnetic field coil system, the modulation patterns of critical current Ic were observed for three different field directions. They were successfully used to measure the magnetic properties of a molecular ferrimagnetic microcrystal (23x17x13 microm3), [Mn2(H2O)2(CH3COO)][W(CN)8]2H2O. The magnetization curve was obtained in magnetic field up to 0.12 T between 30 and 70 K. This is the first to measure the anisotropy of hysteresis curve in the field above 0.1 T with an accuracy of 10(-12) J T(-1) (10(-9) emu) with a HTS micro-SQUID magnetometer.